L2 & L3 Gigabit Ethernet VME switch
This product is in End of Life (EOL).
Please use the ComEth 4070e product replacement.
ComEth4070a is built on the latest generation of Gigabit switch engine and PHY transceiver. It combines a layer 2+ switch and a full layer 3 router in a single equipment with an optimized power consumption.
ComEth4070a supports full-wire speed L2 bridging and L3 routing with L2-L4 advanced traffic classification, filtering and prioritization. For instance, it can provide strict priority traffic needed for delay-sensitive or critical applications.
ComEth4070a ports are compatible with VME64x system. Basically twenty GigaEthernet are routed on the P0 P2 rear connectors. The four remaining Giga Ethernet channels are available on the front or on P2. The front option can provide four 1000BT (RJ45) ports or optionally 1000SX/LX fiber channels. The Gigabit transceivers select automatically the media with activity.
Auto-crossover, auto-polarity, auto-negotiation and automatic MAC address management make ComEth4070a a true Plug&Play switch. The Marvell Virtual Cable tester allows a remote identification of potential cable malfunctions as excessive pair skew, cable opens, impedance mismatch...
This switch is fully functional compatible with ComEth4000a, 40x0 range.
24 10/100/1000 Ethernet ports with a full-wire speed switching capacity of up to 37Mpps.
Layer2 Switching capabilities:
16K entries forwarding database
Automatic or controlled learning and aging routing table
Full-line rate switching engine
Port and MAC access control
Flow control and backpressure
9 KB Jumbo Frame
IPV4 IGMP IPV6 MLD snooping
MAC address transplanting for Rapid Reconfiguration 802.1w
Link aggregation static or LACP
Multicast rate limiting
Egress rate shaping with rate ranging port from 64K to 1Gbs
Minimal bandwidth guarantee per traffic Class
4K actives VLANs
4K Bridge multicast groups
Flexible VLAN assignment 802.1Q port -based, protocol based 802.1v, service Vlans 802.1ad, Policy based Vlans
Quality of Service engine:
8 priority queues per port
Traffic Class assignment according to 802-1p tag, MAC address, Port, DiffServ CP or Policy engine
L3 IP V4 & V6 routing:
1K UC ARP entries
RIPV2, OSPF V2 Routing
802.1X Port authentication
Virtual cable tester On-Line
Flexible management tools:
Web or CLI management
Standard & private MIBs
Enhanced Port mirroring
Easy software updating
24 auto-sensing 10/100/1000Mbs ports.
Optional front SX or LX Fiber (LC) interface 802.3u compliant.
Auto-Negotiation with Downshift
Automatic MDI/MDIX crossover for all 3 speeds of operation.
Automatic polarity correction.
Online virtual cable tester.
Optional fast Ethernet out of band management port
Layer 2 switching
802.1D/Q Compliant with a full-line rate Ethernet switching engine
16000 MAC address database automatic or controlled aging and learning mechanism,
Tag extraction and insertion
(802.1p), Jumbo frames up to 9KBytes.
Back pressure for half-duplex, IEEE802.3x for full-duplex.
Discard broadcasts above critical threshold.
Link aggregation with static or dynamic LACP (7 trunks of 8 channels)
Enhanced port mirroring.
IGMP & MLD snooping.
802.1Q compliant : supports Layer 2 domain partitioning of up to 4000 active VLANs.
VLAN is flexibly programmed to any value from 1 to 4094 Protocol-based VLAN (802.1v) or Port-based VLAN (802.1v).
Port and MAC access control compliant with 802.1X authentication.
Eight queues per port.
Minimal and maximal bandwidth affectation per traffic class using weighted round robin and strict priority scheduling.
72 quality of services profiles for traffic class drop precedence
STP/RSTP provides redundant link support. Rapid STP capability for minimizing STP convergence.
Rear Transition module routes ports to the rear panel
Please consult us
Onboard firmware is implemented with comprehensive Built-In Test (loopback mode used during the diagnostic), maintenance functions and network (BootP) updating functions.
Management software provides a wide range of configuration L2/3 functions on any port: transmission speed/mode, VLAN, STP parameters, mirroring, QoS, etc.
Supervision get lots of information in real time on the switch.
MIB, RMON counters and private informations are reachable from SNMP agent, web-browser and CLI for L3 functions.
This Open Application, named SWITCHWARE, is carried out by a PowerPC processor.
Front panel LEDs
Power supply and Switch status
Switched ports : activity & link
5V only or 5V-3.3VDC balanced Power Supply
|Criterion||Standard||Extended||Rugged||Conduction-cooled 71°C||Conduction-cooled 85°C|
|Operat. Temp.||0 to 55°C||-20 to 65°C||-40°C to 71°C or 85°C (*)||-40°C to 71°C
at the thermal interface (*)
|-40°C to 85°C
at the thermal interface (*)
|Rec. airflow||1 .. 2 m/s||2 .. 3 m/s||2 .. 5 m/s||-||-|
|Oper. HR% no cond.||5 to 90%||5 to 95%||5 to 95%||5 to 95%||5 to 95%|
|Storage Temp.||-45°C to 85°C||-45°C to 85°C||-45°C to 100°C||-45°C to 100°C||-45°C to 100°C|
|Sinusoidal Vibr||2G [20..2000]Hz||2G [20..2000]Hz||5G [20..2000]Hz||5G [20..2000]Hz||5G [20..2000]Hz|
|Random Vibr||0.002g2 /Hz
|Shock 1/2 Sin. 11ms||20G||20G||40G||40G||40G|
Single Board Computers
Single Board Computers